Official Luthiers Forum! • View topic

Board index » Forum Archive

All times are UTC - 5 hours

Dish Sanding Paper?

Page 1 of 1

[ 10 posts ]

Print view

Previous topic | Next topic

Author

Message

ATaylor

Post subject:

Posted: Sat Feb 25, 2006 3:29 pm

Cocobolo

Joined: Sat Dec 31, 2005 10:05 am
Posts: 227
Location: United States

Is there a source for sanding paper for sanding dishes? I've had marginal success with trimming standard paper to the concave form but want that perfect fit. I've seen dishes with paper already applied - where to they get that.

Top

Alain Desforges

Post subject:

Posted: Sat Feb 25, 2006 4:06 pm

Brazilian Rosewood

Joined: Tue Dec 20, 2005 7:46 am
Posts: 2227
Location: Canada

Shane from HighMountain carries it as well. Top notch quality...

_________________
I'd like to be able to prove, just for once, that money wouldn't make me happy...

Top

ATaylor

Post subject:

Posted: Sat Feb 25, 2006 4:33 pm

Cocobolo

Joined: Sat Dec 31, 2005 10:05 am
Posts: 227
Location: United States

Thanks Guys - should have thought that is the case!

Top

tippie53

Post subject:

Posted: Sun Feb 26, 2006 12:21 am

Koa

Joined: Thu Feb 17, 2005 3:38 pm
Posts: 1542
Location: United States

I carry 24 inch 80 and 100 grit . PSA back that means the stickie is on the back
john
$15 plus ship

Top

John Mayes

Post subject:

Posted: Sun Feb 26, 2006 3:15 am

Brazilian Rosewood

Joined: Sat Jan 08, 2005 3:37 am
Posts: 2670
Location: United States
First name: John
Last Name: Mayes
City: Norman
State: OK
Focus: Build
Status: Professional

Econabrasives.com has them too. They can pretty much make any and all
sandpaper you could want, at great prices too.

_________________
John Mayes
http://www.mayesluthier.com

Top

tippie53

Post subject:

Posted: Sun Feb 26, 2006 4:11 am

Koa

Joined: Thu Feb 17, 2005 3:38 pm
Posts: 1542
Location: United States

That may be cost effective but you have lots of joints to contend with. Once you use a 1 pc disk you can see the big advatage.

Top

Shane Neifer

Post subject:

Posted: Sun Feb 26, 2006 4:31 am

Brazilian Rosewood

Joined: Thu Aug 04, 2005 7:50 am
Posts: 3152
Location: Canada

Michael, I agree with John, I tried using floor sanding pads that were PSA (12x16 or something like that). I had a couple of edges that lifted and once that happens they don't go back down. When I took them off they took part of the dish with them. That wasn't too big of a deal for me as I have the ability to spin the dish again and take off a thin layer but for those that can't spin them that means a lot of filling and sanding with the hope that you can maintain the even curve. One piece is the way to go, indeed! 80 grit is all I use...and sell!

Shane

_________________
Canada

Top

John Mayes

Post subject:

Posted: Sun Feb 26, 2006 5:02 am

Brazilian Rosewood

Joined: Sat Jan 08, 2005 3:37 am
Posts: 2670
Location: United States
First name: John
Last Name: Mayes
City: Norman
State: OK
Focus: Build
Status: Professional

yeah for sure one piece. They are not very expensive, no joints to bump
over and it's just plain easier to deal with and does a better job!

_________________
John Mayes
http://www.mayesluthier.com

Top

Page 1 of 1

[ 10 posts ]

Board index » Forum Archive

All times are UTC - 5 hours

Who is online

Users browsing this forum: No registered users and 11 guests

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to: